老熟女老女人老熟妇av,国产日韩欧美在线播放,日韩色在线精品视频观看,国产的视频在线观看无遮挡

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push and pull the cylinder Sold to Costa Rica

Release time:2023-11-21 09:56:01 Hits: Current position: Home > News

This article mainly introduces:

Costa Rica hydraulic cylinder,push and pull the cylinder manufacturer,push and pull the cylinder

Costa Rica push and pull the cylinder

(Costa Rica push and pull the cylinder,produced by Hengyu Hydraulic Cylinder Factory)

push and pull the cylinder are widely used in Costa Rica,because of long service life,smooth movement,high work efficiency.So our company has designed push and pull the cylinder for customers from Costa Rica.

Introduction to push and pull the cylinder:

How the cavitation of the push and pull the cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the push and pull the cylinder, resulting in corrosive damage to the parts.

In use, the push and pull the cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the push and pull the cylinder.

When the push and pull the cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the push and pull the cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

When installing the push and pull the cylinder pipe, the pipe should be cleaned after installation, and should not pass through the push and pull the cylinder block, and the by-pass pipe must be installed in front of the oil port of the push and pull the cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the push and pull the cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the push and pull the cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about push and pull the cylinder:

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
晋宁县| 德钦县| 杭锦旗| 西昌市| 洛南县| 饶平县| 亚东县| 河池市| 崇阳县| 田林县| 秦皇岛市| 株洲市| 成武县| 乌兰察布市| 乳山市| 财经| 淳安县| 伊金霍洛旗| 汕尾市| 喀喇| 隆尧县| 汝州市| 健康| 临桂县| 浪卡子县| 庆阳市| 三原县| 临沭县| 建始县| 白河县| 定日县| 唐河县| 通渭县| 成武县| 调兵山市| 德清县| 永嘉县| 尖扎县| 林西县| 内黄县| 岑溪市|