老熟女老女人老熟妇av,国产日韩欧美在线播放,日韩色在线精品视频观看,国产的视频在线观看无遮挡

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Costa Rica

Release time:2023-11-08 15:23:54 Hits: Current position: Home > News

This article mainly introduces:

Costa Rica hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Costa Rica trunnion cylinder

(Costa Rica trunnion cylinder,produced by Hebei Hengyu company)

trunnion cylinder are widely used in Costa Rica,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed trunnion cylinder for customers from Costa Rica.

Introduction to trunnion cylinder:

trunnion cylinder buffer valve inspection and maintenance: For the valve buffer trunnion cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

The trunnion cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

If the trunnion cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the trunnion cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow trunnion cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the trunnion cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the trunnion cylinder includes the leakage caused by excessive wear of the trunnion cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and trunnion cylinder, and the phenomenon of "pulling the trunnion cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

In use, the trunnion cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the trunnion cylinder.

Answers to some questions about trunnion cylinder:

What is the thin cylinder used for?
The principle is no different from ordinary cylinders, that is, the installation space is small, the formation is small, and it is suitable for some special occasions. For example, the space is compact and the place of small travel is used.

How does the cylinder of the shearing machine work?
Plate shear is a machine that cuts a sheet with a reciprocating straight motion from one blade to another. Through the moving upper blade and the fixed lower blade, the shear force is applied to the metal sheet of various thicknesses with a reasonable blade gap, so that the sheet is broken and separated according to the required size. Shearing machine belongs to one of the forging machinery, the main role is the metal processing industry. Products are widely used in aviation, light industry, metallurgy, chemical industry, construction, shipbuilding, automobile, electric power, electrical appliances, decoration and other industries to provide the required special machinery and complete sets of equipment. Working principle: The hydraulic system is used to drive the hydraulic cylinder to output a strong shear force to complete the shearing work.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
江华| 宣汉县| 阜新| 景泰县| 福州市| 长宁区| 东辽县| 镇沅| 陆丰市| 富源县| 永春县| 平顶山市| 麦盖提县| 微山县| 门头沟区| 建宁县| 德惠市| 泸州市| 长子县| 永康市| 原阳县| 麻栗坡县| 乃东县| 高州市| 香格里拉县| 潮安县| 湟源县| 民乐县| 涞源县| 巴林左旗| 山丹县| 井陉县| 扬州市| 瑞安市| 黑山县| 乌苏市| 绿春县| 乐都县| 那坡县| 新巴尔虎左旗| 巴林右旗|