老熟女老女人老熟妇av,国产日韩欧美在线播放,日韩色在线精品视频观看,国产的视频在线观看无遮挡

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to S.Africa

Release time:2023-11-12 11:05:45 Hits: Current position: Home > News

This article mainly introduces:

S.Africa hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

S.Africa trunnion cylinder

(S.Africa trunnion cylinder,produced by Hebei Hengyu company)

trunnion cylinder are widely used in S.Africa,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed trunnion cylinder for customers from S.Africa.

Introduction to trunnion cylinder:

The internal leakage of the trunnion cylinder should be prevented when the trunnion cylinder is used. The internal leakage of trunnion cylinder includes the leakage caused by excessive wear of trunnion cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

If the seal of the trunnion cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

When the trunnion cylinder is in use, ensure that the trunnion cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

Regular maintenance of the trunnion cylinder includes: regular tightening, trunnion cylinder fastening screws and gland screws, trunnion cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the trunnion cylinder once a year. Clean regularly, the trunnion cylinder is cleaned every other year, and the seals are replaced while cleaning.

Answers to some questions about trunnion cylinder:

Why does the hydraulic cylinder ring?
1 Air intrusion into the hydraulic system is the main reason for noise 2 The relief valve is unstable, such as due to the improper combination of the slide valve and the valve hole or the contact of the cone valve and the seat is stuck by dirt, the damping hole is blocked, the spring is crooked or fails to make the spool stuck or move in the valve hole, causing system pressure fluctuation and noise. 3 Improper adjustment of the reversing valve causes the spool of the reversing valve to move too fast, resulting in reversing impact, resulting in noise and vibration. 4 Mechanical vibration, such as long tubing, elbow more and not fixed, when the oil flow through, especially when the flow rate is high, easy to cause pipe shaking; The rotating part of the motor and hydraulic pump is unbalanced, or the alignment is not good during installation, or the coupling is loose, etc., which can produce vibration and noise.

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
垣曲县| 南乐县| 财经| 秭归县| 无棣县| 铜梁县| 襄汾县| 陆良县| 南通市| 中牟县| 会昌县| 垫江县| 东乌珠穆沁旗| 通州区| 内乡县| 九寨沟县| 自贡市| 峡江县| 双辽市| 将乐县| 育儿| 高淳县| 郴州市| 黑水县| 南昌市| 华池县| 南丹县| 阳东县| 万安县| 英德市| 台中县| 吐鲁番市| 青神县| 门源| 台中县| 信宜市| 喜德县| 昌乐县| 宁夏| 赫章县| 克拉玛依市|